Ｎａｎｊｉｎｇ Ｒｕｉｐｉｎｇｄｅ Ｅｌｅｃｔｒｏｍｅｃｈａｎｉｃａｌ Ｅｑｕｉｐｍｅｎｔ Ｃｏ．， Ｌｔｄ
MATERIAL SAFETY DATA SHEET
KLINGERSIL C-4243
Page 1 of 7
1 - IDENTIFICATION OF THE MATERIAL AND SUPPLIER
Product Name
Other Names
KLINGERSIL C-4243
Compressed Non-Asbestos Fibre Sheeting/Jointing/Gaskets KLINGERSIL C-4243
Recommended Use High temperature gasket material
Supplier KLINGER Limited (ABN 95 008 679 838)
38 McDowell St Welshpool WA 6106 AUSTRALIA
Tel +61 (0)8 9350 1100 (0800 – 1700 Australian Western Standard Time – GMT +8 hrs) Fax +61 (0)8 9350 6200
2 - HAZARDS IDENTIFICATION
Not classified as hazardous according to the criteria of NOHSC.
The product is considered harmless to health and the environment in the form supplied and if stored and handled in the correct manner – see Section 7. No hazards are known based on present information.
3 - COMPOSITION/INFORMATION ON INGREDIENTS
Ingredient CAS Proportion
Aluminia Silicate 1332-58-7 30 – 60% Calcium Metasilicate (Wollastonite) 13983-17-0 10 - < 30% Nitrile Butadiene Rubber 9003-18-3 10 - < 30% Precipitated Silica 112926-00-8 10 - < 30% Organic Fibre (Cellulose) 9004-34-6 10 - < 30%
Rev. Feb 2010
南京瑞平德机电设备有限公司 Ｔｅｌ：＋８６ ２５ ５８７３１８５６ Ｆａｘ：＋８６ ２５ ５８７４８８０６ Ｅｍａｉｌ：ＲＰＤ１００＠１２６．ＣＯＭ
MATERIAL SAFETY DATA SHEET
KLINGERSIL C-4243
Page 2 of 7
4 - FIRST AID MEASURES
Inhalation
Dust arising from working the product should be treated as nuisance particulate material. Inhalation of dust may cause irritation to the mucous membranes and upper respiratory tract. Movement of exposed individual to fresh air is recommended. May cause irritation to individuals with sensitive skin. Wash skin with soap and water. Launder heavily contaminated clothing before reuse. If prolonged irritation occurs, seek medical advice. May cause mechanical irritation in contact with eyes. Remove small solid particles and rinse with water for a minimum of 15 minutes. In all cases of eye contamination it is a sensible precaution to seek medical advice.
Not hazardous. Not a likely source of exposure. If ingested, give plenty of fluid to assist passage through system. Seek medical attention if irritation occurs.
Skin Eye
Ingestion
5 - FIRE FIGHTING MEASURES
Suitable Extinguishing Media
Hazards from Combustion Products
Water, carbon dioxide, powder extinguishers, foam extinguishers In case of combustion, the same gases are produced as with burning rubber. The following may be produced in case of fire: Carbon monoxide; carbon dioxide; sulphur oxides; nitrous gases (NOx);
irritating/caustic, combustible as well as poisonous carbonisation gases.
Breathing apparatus and eye protection must be worn to protect from dust, fumes and burning rubber.
Precautions for Firefighters
and Special Protective Equipment
6 - ACCIDENTAL RELEASE MEASURES
Rev. Feb 2010
南京瑞平德机电设备有限公司 Ｔｅｌ：＋８６ ２５ ５８７３１８５６ Ｆａｘ：＋８６ ２５ ５８７４８８０６ Ｅｍａｉｌ：ＲＰＤ１００＠１２６．ＣＯＭ
MATERIAL SAFETY DATA SHEET
KLINGERSIL C-4243
Page 3 of 7
Emergency Procedures
Methods and Materials for Containment and Cleanup
Additional
Fire: See Section 5 Personal: See Section 4
Environmental: No known environmental hazards exist. Approved vacuum cleaners with high efficiency filters (HEPA) conforming to AS3544 or equivalent must be used to clean areas.
In the case of improper use (see Section 8) fine dust may result. Adequate suction and filtering of the exhaust air should be ensured.
7 - HANDLING AND STORAGE
Handling
No special precautions necessary when handling the material in its finished form as the synthetic mineral fibres are encapsulated in a rubber matrix. However, whenever further processing of
sheets/gaskets is undertaken, the potential for the release of fibres exists. See Section 8.
Store in a cool, dry, well ventilated area removed from foodstuffs. Ensure ventilation is adequate to disperse vapours emitted from the binding material. Vapours may include traces of carbon monoxide, carbon dioxide, oxides of nitrogen and formaldehyde. Material should not be stored in the vicinity of heat sources. Material is only flammable through the effects of intensive heat. Excessive heat or humidity in the storage area may diminish the product’s performance in its intended application.
THIS MATERIAL MUST NOT BE DRILLED, SAWED, GROUND, SANDED OR SUBJECTED TO ANY OTHER DUST PRODUCING PROCESS.
Storage
8 - EXPOSURE CONTROLS/PERSONAL PROTECTION
National Exposure Standards (Time-Weighted Averages)
Biological Limit Value
Precipitated Silica: 10mg/m3 ES-TWA Nitrile Butadiene Rubber: 50ppm ES-TWA Aluminia Silicate: 10mg/m3 ES-TWA Cellulose: 10mg/m3 ES-TWA No Biological Limit Value allocated.
Rev. Feb 2010
南京瑞平德机电设备有限公司 Ｔｅｌ：＋８６ ２５ ５８７３１８５６ Ｆａｘ：＋８６ ２５ ５８７４８８０６ Ｅｍａｉｌ：ＲＰＤ１００＠１２６．ＣＯＭ
MATERIAL SAFETY DATA SHEET
KLINGERSIL C-4243
Page 4 of 7
Engineering Controls
Ensure adequate ventilation exists to maintain air concentrations below exposure standards. Do not inhale dust/fibres. Use localised extraction or wet methods of work to control dust levels.
No special precautions necessary when handling the material in its finished form as the synthetic mineral fibres are encapsulated in a rubber matrix. However, whenever further processing of sheets/gaskets is undertaken, the potential for the release of
particulates exists. In the case of particle generation exceeding the above-noted National Exposure Standards, recommended PPE are rubber/PVC
gloves, coveralls, safety glasses and a P2 particulate (AS1716 or equivalent) respirator. When removing embrittled or spent material or when high levels or dust exist a full-face class H particulate cartridge respirator or full-face positive pressure demand airline respirator (AS1716 or equivalent) is
recommended. Good hygiene practices must always be maintained.
Personal Protective Equipment
9 - PHYSICAL AND CHEMICAL PROPERTIES
Appearance
Odour pH
Vapour Pressure
Vapour Density
Boiling Point/Range
Freezing/Melting Point
Flashpoint
Solubility (water)
Form: Colour:
Sheets or cut gaskets
Green one side, oilve other
May smell slightly of rubber Not applicable Not applicable Not applicable Not applicable Not applicable Not applicable Insoluble
Rev. Feb 2010
南京瑞平德机电设备有限公司 Ｔｅｌ：＋８６ ２５ ５８７３１８５６ Ｆａｘ：＋８６ ２５ ５８７４８８０６ Ｅｍａｉｌ：ＲＰＤ１００＠１２６．ＣＯＭ
MATERIAL SAFETY DATA SHEET
KLINGERSIL C-4243
Page 5 of 7
Specific Gravity/Density 1.75g/cc
Additional Elastomer carbonisation and decomposition occurs at high
temperatures.
10 - STABILITY AND REACTIVITY
Chemical stability Stable under intended operating conditions.
Conditions to Avoid Not known
Incompatible Materials Not known
Hazardous Decomposition Products Decomposition of rubber at high temperatures.
11 - TOXICOLOGICAL INFORMATION
The material in its finished form presents no known health hazard. Synthetic mineral fibres (SMF) is a collective term used internationally to describe fibres such as fiberglass, rockwool and ceramic fibres. The release of SMF into the air is a health risk hence the adoption of an exposure standard of 0.5f/mL (TWA), for respirable fibres according to the National Commission – Worksafe Australia. For non-respirable SMF a secondary (complementary) exposure standard of 2mg/m3 is proposed by Worksafe Australia. This proposed secondary standard is established to minimise upper respiratory tract irritation from non-respirable fibres. It does not take precedence over the respirable fibre standard. Worksafe has determined not to classify SMF as a suspected carcinogen due to the lack of supporting evidence.
THIS MATERIAL MUST NOT BE DRILLED, SAWED, GROUND, SANDED OR SUBJECTED TO ANY OTHER DUST PRODUCING PROCESS.
12 - ECOLOGICAL INFORMATION
Ecotoxicity
Persistence and Degradability
Not known. Insoluble in water, precipitates. Not known. Not biologically degradable (self-classification).
Rev. Feb 2010
南京瑞平德机电设备有限公司 Ｔｅｌ：＋８６ ２５ ５８７３１８５６ Ｆａｘ：＋８６ ２５ ５８７４８８０６ Ｅｍａｉｌ：ＲＰＤ１００＠１２６．ＣＯＭ
MATERIAL SAFETY DATA SHEET
KLINGERSIL C-4243
Not known
Page 6 of 7
Mobility
13 - DISPOSAL CONSIDERATIONS
Disposal Methods
No special requirements exist. Dump on industrial
depositories. Seal waste dust in heavy duty plastic bags (200 microns minimum). Do not dispose of in an incineration system under any circumstance. Local, state and federal statutory regulations must be observed. Not applicable
Special Precautions
14 - TRANSPORT INFORMATION
UN Number None allocated
UN Proper Shipping Name None allocated
Class and Subsidiary Risks Not relevant
Packing Group Not relevant
Special Precautions for User Do not transport with Explosives, Oxidising agents,
Organic peroxides and foodstuffs. In sheet and cut gasket form there is no risk associated with the product under normal transport conditions. Not defined as a Dangerous Good by the Australian Code for the Transport of Dangerous Goods by Road and Rail.
Hazchem Code None allocated
15 - REGULATORY INFORMATION
Regulations for dangerous materials not applicable.
Rev. Feb 2010
南京瑞平德机电设备有限公司 Ｔｅｌ：＋８６ ２５ ５８７３１８５６ Ｆａｘ：＋８６ ２５ ５８７４８８０６ Ｅｍａｉｌ：ＲＰＤ１００＠１２６．ＣＯＭ
MATERIAL SAFETY DATA SHEET
KLINGERSIL C-4243
Page 7 of 7
16 - OTHER INFORMATION
The information presented is based on the present level of knowledge and experience.
All information and recommendations contained in this publication are to the best of our knowledge. Since the conditions of use are beyond our control, users must satisfy themselves that products are suitable for the intended processes and applications. No warranty is given or implied in respect of information and recommendations or that any use of the products will not infringe rights belonging to other parties. In any event or occurrence, our liability is limited to our invoice value of the goods delivered and properties without notice.
END OF MSDS
Rev. Feb 2010
南京瑞平德机电设备有限公司 Ｔｅｌ：＋８６ ２５ ５８７３１８５６ Ｆａｘ：＋８６ ２５ ５８７４８８０６ Ｅｍａｉｌ：ＲＰＤ１００＠１２６．ＣＯＭ
因篇幅问题不能全部显示，请点此查看更多更全内容